Tyre Pressures and Monitors

To keep you van stable and tyres from exploding you need to have the right tyre pressures in you van tyres as well as your car tyres.

The easiest way is to simply read the compliance plate on the van, it should have the recommended cold pressure listed on it. Your car should have the pressures listed on a sticker that’s usually on the door jamb or door fame, sometimes the glovebox or worst case, read the manual!

Ok, so what to do if you don’t have the info for the van, or the tyres are different to original or the plate doesn’t have the info? All is not lost, you can use the following calculation to get a great starting point.

Firstly have a look at the van tyres and look for the maximum weight and maximum pressure, use the figures for single tyre not dual if it lists both (dual is two tyres side by side, not dual axle).

Tyre pressure information from the tyres on our van

Next you need to know the weight of your van on the wheels, so that’s the Gross Trailer Mass or GTM (or the ATM minus Ball weight). This needs to be the normal operating weight, not the tare, so best to weigh it when fully loaded for your trip. If you are not able to weigh it then work with maximum loads as most vans will be running very close to this anyway.

Now comes the mathematics..

  1. Divide the GTM by the number of tyres on your van, so we have the weight per tyre.
  2. Now take the actual weight per tyre just calculated and divide that by the maximum weight listed on the tyre.
  3. Multiply that answer by the maximum pressure written on the tyre and bingo, there is your cold tyre pressure.

Example:

  1. Our van has 4 tyres and a GTM of close enough to 3000kg. That’s 3000/4 = 750kg per tyre.
  2. Our tyres are listed as max 1250kg. So 750 / 1250 = 0.6
  3. Our tyres are listed as max 80psi. So 0.6 x 80 = 48psi.

Now put away your calculator, I built one for you!

You can also do the same calculation for your car tyres, however you have to remember they will most likely have different loads on them front and rear.

So now what, set it and forget? Well you can, this would be close enough, however ideally you want to monitor, test and fine tune. There are two common methods here.

First let’s look at the 4 (or 6) PSI rule, which is also known as a 12% rule and based on the pressure in the tyre increasing by approximately 1psi for every 5° increase in temperature (that’s a broad average based on normal pressures around 40PSI). Start with cold tyres, as in sitting still for at least an hour, measure the pressure. Then drive for a good time (an hour is perfect) and measure again. On a P or passenger rated tyre thats normally around the 30psi mark it will increase approximately 4psi, and on an LT or light truck rated tyre that’s normally around the 50psi mark it will increase by 6psi when inflated to a correct pressure. In both cases this is around 12% increase. If it raises by more, it was too low to start and the tyre is over heating so add some pressure (the flexing of the sidewalls warms the tyre up more). If it only raises a small amount it’s too high to start and drop them a little.

Second method is the chalk test. Get tyres to operating temp, scrub a line of chalk across the tyre then drive in a straight line for around 50m. Now check the chalk – has it rubbed off the edges more than the middle? Too low, pump it up a bit. Has it rubbed off more in the middle? To high, let some air out. has it worn evenly across the tread? Perfect!

This is the basis for the chalk wear:
Left = to low and edge chalk wears, middle = too high and centre chalk wears, right = OK and wear is even across the tyre

How do you monitor them?

On the Jeep its pretty easy, it comes with TPMS or Tyre Pressure Monitoring System inbuilt. However the Caravan does not so I have installed one so I can keep an eye on them. Last thing I want is to run over a nail or screw in the middle of nowhere then not realise the tyre is deflating, overheating then shredding itself, potentially creating a sway event that rolls the caravan.

So what to use? First one I bought looked great seemed to work great too, it was from ODB2 Australia and had a windscreen mounted solar charged display. The only issue I found was the range wasn’t good enough and the display would loose connection with the tyre senders after a while of driving in a straight line (highway driving). After discussions I ordered a repeater, then over the next 9 months received a replacement repeater then two full replacement kits. None of them made any difference. After much testing (Dave the Geek at work) I was able to prove the repeater was connecting to the wheel senders but not to the display and the display was only seeing the senders directly. A year after purchase it was returned for a refund. The below picture is showing the right side tyres missing off the display, left disappeared a few minutes later (an hour of driving with no signal from the tyre and that tyre indicator goes blank). This was a real shame as the unit was small and unobtrusive. (discussions appear to show there was an issue with firmware versions of the display not being compatible with the repeater).

OBD2 Australia TPMS – great concept

I now have the Safety Dave TPMS system at 4 times the price, the display is larger and bit more cumbersome to mount and does not have a solar charger so has to be plugged into USB every few weeks, but instead of a 8 to 10 m range it reportedly has a 200m range. First long drive coming up in a few days where I will be able to check out how it works. It was purchased from Everything Caravans – an online store in Victoria. Great service and prices, highly recommend them.

Update 6th June 2022: Nice long drive from Melbourne to Adelaide and same issue. Driving in a straight line the sensors drop off the display after about 45 minutes. Chat with Safety Dave help line and we re-programmed the link and parameters as they said this is usually the problem. Next drive was Adelaide to Port Augusta – same issue. Called them again and was asked it this was with the booster running.. I replied the what?? Anyway, it has now been sent back and a replacement will be sent soon with a booster apparently. Will see how this one works!

Update 4th July 2022: booster received in Coober Pedy and installed, now a thousand or so km later of towing it hasn’t missed a beat. So yes, the booster solved my issues. It came with a cigarette lighter adaptor attached and I have an outside TV cabinet with a cigarette socket in it, so have just left it in there for now.

Safety Dave TPMS

Hope that helps!

You may also like...

Leave a Reply

Your email address will not be published.